専用治具

Selection of an attachment is very important, and it will bring out the full-capability of the testing machine. Almost every IMADA testing machine can measure the both "tensile" and "compression". Therefore the test of "tension", "compression", "bending", "stripping", and so on is possible by selecting the correct attachment for the testing purpose.
We have more special attachement besides the items listed in this web site.
We design the attachment which meets your requirement. Please feel free to contact us and let us know your requirement.

■Caution when choosing the right attachment
○	Testing load has to be lower than the maximum load of the attachment.
○	The weight of the upper attachment has to be lower than the 10% of the maximum load of the load cell.If the maximum load of the load-cell is very small, it is recommended to adjust the testing machine with the attachment attached.
○	Make sure the size of the connecting rod is correct. Chart below show the size of the screw for upper/lower attachment.
○	If you plan to test unique and special materials, it is highly recommended to perform the sample testing to choose the right attachement.

■SELECT FROM THE LIST BELOW

Film Grip	Flat Chuck	Drill Chuck(Jacob's Chuck)
Wire Winding Grip	Wedge Grip	Tape Grip
Pantagraph Grip

Bend Test Stand	Flat Head Compression Attachment	Miscellaneous Attachement
Vise Grip	90 degree peel table
Chip Shear Test Attachment/Wire Terminal Grip/Paper Chuck

X-Y Table, Y-Z Table	T-nut, Connecting Rod/Universal Joint/Connecting Joint
Special Attachment Exsamples

■Regarding the mounting of the attachment

It is necessary to mount the attachment to our Testing Machine. And to bring out the full-capability of the testing machine, it is necessary to choose the right attachment. Therefore, attachment needs to be selected from our list or manufactured by customers. Below is the chart that shows a mating relations of our attachment. Please refer to the following charts when you mount the attachment or when you manufacture the attachment by yourself.

●Mounting Upper Attachment
Upper attachment is to be mounted by screwing it into the load cell. Size of the screws are as follows.

Max. Load	Less than 500N	1kN to 10kN	20kN	30kN to 50kN	100kN
Model	Push-Pull Scale Digital Force Gauge SV-55C SV-52NA SV-52CA SDT-52NA SDT-52CA	SV-100NA SV-100CA SV-200NA SV-200CA SV-201NA SV-201CA SV-301NA SV-301CA SDT-201NA SDT-201CA SVF-500NA SVF-500CA SDWS(up to 10kN) SDW-1002 SDW-1012	SDWS-2002 SDWS-2012 SDW-2002 SDW-2012	SDW-3002 SDW-5002	SDW-9902
Size of the Screw	M6P1	M12P1.75	M16P1.5	M24P2	M32P2

*Size of screw for the Push-Pull Scale and Digital Force Gauge with the maximum load range from 1kN to 3kN is M10P1.5.
*Mounting the small max. load attatchment to the Testing Machine with the large amount of max. load requires reducing connecting screw.

●Mounting Lower Attachment
Surface table is pre-installed for our Testing Machines and Push-Pull Stands. T-shaped channel is designed to mount the lower attachment by using 2 pairs of T-nuts and bolts. Shape of the T-shaped channel and the size of the bolts are as follows;

Model	SV-5 SV-55C SV-52NA SV-52CA SDT-52NA SDT-52CA	SV-100NA、 SV-100CA SV-200NA、 SV-200CA SV-201NA、 SV-201CA SV-301NA、 SV-301CA SDT-201NA、SDT-201CA SVF-500NA、SVF-500CA	SDWS-0202 SDWS-0212 SDWS-0502 SDWS-0512	SDWS-1002 SDWS-1012 SDW-1002 SDW-1012 SDW-2002 SDW-2012	SDW-3002 SDW-5002	SDW-9902
Internal thread size of T-nuts	M8P1.25	M8P1.25	M8P1.25	M12P1.75	M16P2	M20P2.5
Size of T-shape Channel